Link-Seal® modular seals are considered to be the premier method for permanently sealing pipes of any size passing through walls, floors and ceilings. In fact, any cylindrical object may be quickly, easily and permanently sealed, as they pass through barriers, by the patented Link-Seal® modular seal design. Ductile iron, concrete, metal as well as plastic pipes may be hydrostatically sealed within walls to hold up to 20 psig (40 feet of static head). Electrical or telecommunications cable may be sealed within conduit as they enter vaults or manholes. The annular space between carrier pipes passing through casings may be sealed against the entry of water, soil or backfill material.
With a wide variety of hardware/ elastomer combinations, Link-Seal modular seals are easily configured to achieve the best possible match for service conditions encountered. High temperature seals, fire seals (Factory Mutual Approved) and oil resistant seals may be ordered to meet special or unique service applications. For the system approach, metal or non-conductive Century-Line® sleeves with water stops may be ordered with Link-Seal modular seals to ensure correct positioning and a water tight seal of the installation within poured concrete walls.
Link-Seal® modular seals are also available for a wide variety of special applications, temperature extremes, exotic chemical combinations and for “out of round” or non-centered applications. Please contact factory for your special application.

Link-Seal modular seals install in up to 75% less time compared to lead-oakum joints, hand fitted flashings, mastics or casing boots.

Positive hydrostatic seal...
•Link-Seal modular seals are rated at 20 psig (40 feet of head), which exceeds the performance requirements of most applications.

Long seal life...
•Link-Seal modular seals are designed for use as a permanent seal. Seal elements are specially compounded to resist aging and attack from ozone, sunlight, water and a wide range of chemicals. 

Maximum protection against corrosion...
•Standard fasteners have a two-part zinc dichromate and proprietary corrosion inhibiting coating.
•Corrosion resistant 316 stainless steel available for maximum corrosion protection.

Certification/Approvals...
•Factory Mutual Fire Approvals.•Also a wide variety of approvals from various Federal agencies, associations, code groups, laboratories and organizations.

ISO Quality Assurance...
•Link-Seal modular seals are manufactured in an ISO 9001:2000 certified facility.

Configure a Link-Seal modular seal to match your application...
•16 sizes, color coded EPDM, Nitrile & Silicone elastomers may be used with various hardware options to match performance characteristics with service conditions.

  
1. Century-Line Model CS Sleeves in Combinantion with low durometer EPDM (blue) Link-Seal® Modular Seals Century-Line® Model CS Sleeves are ideal for poured wall construction. Made of HDPE thermoplastic, lightweight and easy to handle. Molded-in waterstop and reinforcing ribs serve to anchor the sleeve in the wall and resist pour forces. Nailer end caps are provided to make placement in forms simple and accurate. Sleeves are available in 16 diameters, up to 25, and any length. In the event of a field change they can be shortened with ordinary hand tools.

2. Pre-cast or Cored Wall Openings in Combination with Nitrile (green) Link-Seal Modular Seals
  
3. Model WS Steel Sleeves in Combination with Silicone (grey) Link-Seal Modular Seals
Model WS Steel Sleeves are made from heavy-wall welded or seamless pipe. A full circle waterstop plate acts as positive water seal and anchor to prevent thrust movement. The 2 collar (water-stop) is continuously welded on both sides. Model WS is available in a wide range of diameters and any length. Sleeves are protected by a coating of red primer. Hot dip galvanizing is available on request.    

Link-seal modular seals and hardware options 

Bolt & Nut Specifications     Standard: Carbon Steel Carbon steel, zinc dichromated per ASTM B633 with an additional corrosion inhibiting proprietary organic coating. (passes 1470 hour salt spray test) Tensile Strength = 60,000 psi, minimum.     Option: Stainless Steel ANSI Type = 316, Per ASTM F593-95 Tensile Strength = 85,000 psi, average. Installation Techniques